[ipxe-devel] Netgear WG311v3

[Lorenz Wenner]

llo,

this is my first posting. Since monday I work at a school where they have a pc-pool with 20 hosts. These hosts are connected via wireless only 
and have all the same NIC. The headmaster does not wish the computers to be connected via wired network. I booted one of them from 
sysrescCD and did 

lspci -vv

here is the relevant output.


03:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03)
        Subsystem: Netgear WG311v3 802.11g Wireless PCI Adapter
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 9
        Region 0: Memory at e8110000 (32-bit, non-prefetchable) [size=64K]
        Region 1: Memory at e8100000 (32-bit, non-prefetchable) [size=64K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

I also have booted ipxe from CD and have tried iwstat, but no interfaces were listet. Is there a way to get ipxe over wireless working? To me it 
looks as if there is some space (or what does Region 0, Region 1 mean?)

i should add there is also a wired onboard NIC in every host. here is what lspci -vv said about one of them

03:0b.0 Ethernet controller: Intel Corporation 82541EI Gigabit Ethernet Controller
        Subsystem: IBM Device 0285
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 52 (63750ns min), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at e8120000 (32-bit, non-prefetchable) [size=128K]
        Region 2: I/O ports at 2000 [size=64]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [e4] PCI-X non-bridge device
                Command: DPERE- ERO+ RBC=512 OST=1
                Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
        Capabilities: [f0] MSI: Enable- Count=1/1 Maskable- 64bit+
                Address: 0000000000000000  Data: 0000
        Kernel driver in use: e1000
        Kernel modules: e1000


kind regards
        Lorenz Wenner